Showing posts with label electric guitars. Show all posts
Showing posts with label electric guitars. Show all posts

Friday, February 20, 2009

Binding the Bodies

The bodies are bound. Let me show you what that entails.



A bit of patience is required as I do everything the hard way.

The purfling cutter is again used to score for the rebate.To keep the purfling cutter blade sharp it is honed repeatedly throughout the scoring process. I use polishing compound on window glass. This is also how I keep my chisels razor sharp. What am I talking about? Razors aren't that sharp.The waste is carefully pared away in specific stages. At all times the chisel is never allowed to face good wood. First I shave off the corner.Then I create a new rebate with the chisel, just within the scored lines. This is carved deeper and wider until a paper thin layer is left against each scored edge. This is carefully pared away with the chisel starting in the scored line.I use a little trick to carve the point on the cutaway. Prior to carving the rebate and several times during, I saturate the fibers with superglue. Just a drop or two will soak in right at the tip and you will never loose any cross grain. But you still have to be careful.You get into a rhythm with the carving of the rebate. It is pretty intense work, since you can't make any mistakes, but it is very satisfying.The body bindings are made just like my veneer, ripped on the table saw with a 1 1/4" sawmill blade and a guide fence.Then thicknessed in the sander. I make the bindings slightly thicker than my standard 3/32" veneer so there is a bit more left to work with in final contouring.Sawn into strips that will fit just proud of the rebate, they are allowed to soak in water for a couple of days. This set up with the bottom of a torn dust collector bag works well.The wet strips are run quickly over the hot pipe and when flexible they are tacked down to a tracing of the actual rebate. As they cool and dry the brads are added and the curves are faired with hand pressure.The whole board is then propped up in front of the wood stove to bake for 2 or 3 days.The bindings are an almost perfect fit when they come off the board. Any small flat spots are trued up on the hot pipe and the cutaway is glued in first. Each successive piece overlaps the previous one. A shaped caul faced with sandpaper is used to true up minor discrepancies that show up when the actual binding is offered up to the rebate. Working around the body each piece is laminated in place. Stategicly located clamps allow for continuous clamping pressure all around the curved edge. The glue will scrape very easily off the polished edge of the body, so I don't worry if it drips all over. With this set up I have plenty of time and can saturate both the binding and the rebate with glue.By shaving the first strips back at a very shallow angle a perfect scarf joint is formed. Once pared back and rasped flush the seam is very difficult to locate. This binding is on for good.


Lots of work for one little piece of wood, no? I think it's worth it.

Friday, January 9, 2009

Off to a great start

So, like I said, I have started 4 more electric guitars. I'll bring you up to date:

The bodies are each laminated, with a total of 5 layers. A core with a hand made veneer top and bottom. The core consists of 3 layers. A central panel of 3/4" thickness and a top and bottom panel of about 3/8"+. These individual layers, or leaves, are assembled from strips of clear cherry and maple. The jointing is done with great precision. Note how the boards stay together prior to glue up with no glue or clamping pressure. It's all in the hand work.

The strips of maple and cherry are carefully recovered from salvaged wood. Cutoff and trim pieces gleaned from the scrap bins behind a furniture factory. Here I have all the leaves for 4 bodies. The thicker centers are sanded and trimmed to size in the front.


The cores are then laminated in this press of my own design. Only the bottom two leaves are being glued in this photo with the rest of the stack used to keep things flat, and for lack of room elsewhere to store the stack. The center is laminated first to just the bottom, recieving it's top leaf after the cavities are routed.
The 4th and fifth layers, top and bottom, consist of 3/32" hand sawn veneer and will go on later.
Some folks would say that the hand sawn veneer is what makes my work so special. To this I would reply, "You ain't seen nothing yet!" Here is a sneak peak at what is in store. The Eat Your Heart Out top on the left is in some spectacular flame maple. Curly cherry and heavily figured walunut make the ground for my first Gates of Hell axe on the right.
These get laminated to the top with a compensatory veneer panel laminated to the bottom or back of the guitar. This all makes for one incredibly strong an stable guitar.

I have also started the necks. I'm making 6 of all colors to keep my design options open.
These are two and 3 piece neck blanks gluing up.

Gluing on the headstock can be tricky.

So I will show you how a country woodworker makes it easy. With angled cauls, faced with 120 grit paper. Waxed paper keeps squeeze out from fouling cauls for many uses. My cauls are of white cedar, I recommend a softwood for no marring of head stock.
All by hand, but as you can see, my process is very precise. All of my necks come within about a half a degree of the 14 degree angle I shoot for. Note heavy squeeze out at joint indicating plenty of titebond 3 water proof wood glue. This is a very strong joint and can take all of my weight when clamped to the bench and tested. Even prior to reinforcement with headstock veneer.
Incidently, I am making these necks with a slightly thicker headstock. The Grover locking tuners I have been using are sublime, and require just one wrap, so I want their string holes slightly lower. Building by hand allows for great flexiblity this way, and I am always looking to make things even better.
All in all, I'm off to a great start. Mick at Manlius Guitar is working on my new pickups as we speak. Two more sets of Goats Growl p-90's, a set of Fat Dianes, and his very own Chicago Blues humbuckers for a taste of something new. Still not sure what is going where, though for that matter I don't even know what the finger boards are going to look like yet. To many cool ideas for just four guitars...